Howdy y'all. Looking to print the Avanti V2 at 50%. Any suggestions? I might make the wall thickness a tad thinner w/ pla until I can get more LW and reprint. Would love to see build photos of any of yours!

Do you think it would be possible to scale the STLs to create a 50mm EDF version of your U2 aircraft? Basically print @ 55% size? Or are there too many small details that wouldn't scale properly?

Just completed my Micro Velocity build, 400g take off weight. Used the Zohd Dart drive train spec. Had to design a motor mount to make installing the motor a bit easier. Created servo mount as well. With a 2s 650mah pushed right to the front CofG is as defined. Just need a calm day to maiden

I have printed out all the parts for the Dragon ,but I don't know the exact size or shape of the wire undercarriage. Has anyone made the undercarriage? Would it be possible to get the shape and or the dimensions here on this forum? Thanks.

I am printing the X29 70mm EDF version and am wondering how the EDF is supposed to be mounted. The parts do not take into account the EDF mounting tabs. JD

Hi, Are there any Snapmaker (A250) owners trying to print Dragon or any other model ? . I'm just looking for the best Cura settings. I haven't started to print anything yet, but if someone could give me any hints (I would like to use LW-PLA). This is my second model, I have printed Fouga Magister (d

I have finished printing and building my Quickie. Does anyone have suggested throws for the elevator, ailerons, and rudder for first flight? Thanks!

While working on a VTOL plane, i missed a small VTOL BiCopter to do some testing. So i made this 😎 Hasn't flown yet, so no flight videos (yet)

Files

Anyone had the Mallard out on the water yet? When I was initially looking at the design I was worried that the V-hull would force water directly into the prop during water taxiing. It looks like I was right! I took her out on the water last week and sure enough - right into the propellers! I cha

I have an edf and I am not sure if it would have enough power for the x29. it is a 64mm edf with a 40 amp esc that runs on 3s.

Finished printing and have started assembling this model. I'm planning to use the FT Aura 5 with a Spectrum remote receiver and small, conventional form factor 2.5g servos. I was thinking about using a hot knife to cut ~ 20x8 mm mounting holes with approximate locations marked by blue tape in the at

I'm trying to print part "fuselage 3" without success. I've tried, as the manual says, to print large end down but the 10mm tube for the large carbon wing rod is printed in mid air and I end up with spaghetti. This tube also supports the shell cuts that in turn support the other tubes. In addition

Hello everybody In 2021 I bought the "3 Plane Micro RC Bundle" including the Micro Peregrine, Micro Velocity and the Micro SkiGull. I have probably messed up the file but I am quite sure I will find it in one or the other backup. However it would be more successful to search for if I would know the

https://play.google.com/store/apps/details?id=com.stevokeano.angrycanyon Mode 2 !

I’m thinking if buying the U2 model but only have a 3d printer with bed dimensions of 220 by 200 by 250…. This is below the general advice size from the rc3dprint but will I get away with it?

Hi, do the printed baffles come as a set of 2 or do I need to purchase 2. Thanks

Does the Dragon have any weight issues when printed entirely in PLA; ie is there any need to print any of it with LW-PLA? Any feedback is greatly appreciated.

Hello, I am thinking in building a micro peregrine, but I want to put some FPV gear in there and I was wondering if it will work if I scale it up a little bit, until wingspan is 900-1000 mm. Would it work nicely? Thanks!